welltech Wellgate 3804 in SIP mode

["kevin ling" <kevin.ling (at) amphenol.com.tw>]

Yes,

 

Same configuration as Martin.

1.for incoming call just set the 3804 "hotline" to one sip extension number.

2.for outgoing call, you just using regular dail command to pass the phone number to 3804  (3804 is a 4FXO port device, the call from ip side always pass to FXO Port). You can telnet to the 3804 and enable the one-stage calling function.

 

Regards,

Kevin

---

From: asterisk-users-bounces (at) lists.digium.com [mailto:asterisk-users-bounces (at) lists.digium.com] On Behalf Of Martin Joseph
Sent: Sunday, March 26, 2006 12:13 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] welltech Wellgate 3804 in SIP mode

On Mar 25, 2006, at 6:26 PM, Erick Perez wrote:

> Martin,  i guess im in dumb mode today because i don't get 
>   what you say, may also be because this will be my first welltech to 
>   configure.
> what im trying to do is:
Sorry, I don't know if 
the 3804 actually uses a similar config setup to my 3701a, so it might not be 
you at all.
> remote_voip_gateway-------->asterisk----------->fox/fxs/and_international_voip_providers
> call 
>   will always go -----> this way, no incoming calls from the right of the 
>   diagram side to asterisk.

Ok, then if it is similar to mine, 
all you need to do is set the SIP configuration screen for the wellgate. Look 
under "SIP Config" and "security config". Then to dial, you just use (repeated 
from below):

For outbound ones, I think I just have a regular 
old
Dial(SIP/${EXTEN} (at) 2003} in my dialplan where 2003 is the FXO 
port.

Good Luck,
Marty

PS I had to reflash my device with the 
SIP formware, as it arrived with H323 firmware.


> On 3/23/06, Martin Joseph < ast (at) stillnewt.org> wrote:
> > On Mar 22, 2006, at 10:24 PM, Erick Perez wrote:
> >
> > > Hi, 
> >     does anybody have a working config or tips to connect the welltech
> > > 
> >     wellgate 3804 (4fxo) unit to asterisk via SIP ?
> > > I think I register 
> >     it via SIP with my * box, but when sending calls
> > > from * to the 
> >     wellgate the unit does not pass the call to any of the 
> > > fxo 
> >     ports.
> > >
> >
> > I am using the 3701a, which is a 1 FXO 1 FXS 
> >     deal.
> >
> > The trick for me was the "routing table"  or 
> >     something like that from
> > the Web based configuration 
> >     screen.  There I changed the default for 
> > the FXO to point to 
> >     IP, and the IP to default to the FXO.
> >
> > Then I also have the "line 
> >     configuration" set so the extension I want
> > to ring ie 2020 is the 
> >     "hotline" for the FXO.
> >
> > For outbound ones, I think I just have a 
> >     regular old 
> > Dial(SIP/${EXTEN} (at) 2003} in my dialplan where 2003 is the FXO 
> >     port.
> >
> > HTH?
> > Marty
> >
> > _______________________________________________
> > --Bandwidth 
> >     and Colocation provided by Easynews.com --
> >
> > Asterisk-Users mailing list
> > To UNSUBSCRIBE or update 
> >     options visit:
> >    
> >     http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>
> -- 
>   
>
> -------------------------------------------
> Erick Perez
> Linux 
>   User 
>   376588
> http://counter.li.org/  (Get 
>   counted!!!)
> Panama, Republic of Panama 
>   
> _______________________________________________
> --Bandwidth and 
>   Colocation provided by Easynews.com --
>
> Asterisk-Users mailing 
>   list
> To UNSUBSCRIBE or update options 
>   visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users