pinnacle 310i Problems maybe i2c
- From: KevinLuX <kevinlux (at) karondimonio.it>
- Date: Fri, 10 Feb 2006 12:28:02 +0100
hermann pitton wrote:
Am Donnerstag, den 09.02.2006, 23:27 +0100 schrieb KevinLuX:
Hi all, I have read many times thread about pinnacle 310i, but at moment
not success for me with this card.
with kdetv i can't find channel also with tvtime. I'm from milan and i
have a good coverage of dvb signal
with windows i can take all channel with a very good quality. But my Os
is linux and i have read that
in analog mode this card works but for me no :'(
Here my steps :
configuring the kernel 2.6.14r2 on an gentoo machine :
RTC enable (for tv time) (static) | only V4L device enable in the
section of v4l. (module) | Only I2C_CONFIG enable. (module)
In the IRDA section all disable.
After this i have compile the source extratted from mercurial cvs:
make
make install
after booting machine :
kevinlux (at) eva ~ $ lsmod
Module Size Used by
rivafb 48592 0
vgastate 7616 1 rivafb
saa7134 96032 0
video_buf 15364 1 saa7134
compat_ioctl32 896 1 saa7134
v4l2_common 6208 1 saa7134
v4l1_compat 11908 1 saa7134
ir_kbd_i2c 5712 1 saa7134
ir_common 23044 2 saa7134,ir_kbd_i2c
videodev 6848 1 saa7134
dmesg say ::
saa7133[0]: board init: gpio is 600c000
the same card sometimes has also 600e000, bit 13 high.
saa7133[0]: i2c eeprom read error (err=-5)
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
How is possible that module loads automatically?' no signal in kde tv
for channels.
With eeprom read error I guess only as unknown/generic without tuner.
soi try :
rmmod saa7134
modprobe saa7134 card=81
modprobe saa7134_dvb
with this result
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)
after : tvtime-scanner always nosignal..
i think that's the error is in i2c ... some helps?'
thanks in advance.
Hi,
they used card=77 for analog tv, it has a different vmux connection than
card=81. You don't even get a analog TV picture with card=81.
According to Hartmut the 310i doesn't follow the Philips reference
design and this makes it complicated to support it for DVB-T currently.
If you power cycle/cold reboot the machine, goes the eeprom read error
away using only card=77 for now?
Cheers,
Hermann
Hi Hermann
In this thread
http://marc.theaimsgroup.com/?l=linux-video&m=113863402907172&w=2
i have found the solution for now :
<<saa7133[0]: i2c eeprom read error (err=-5) is solved loading first
tda9887 with port2=1and lager saa7134.>>
So i have unload saa7134 and load first tda9887 and later saa7134. The
error from i2c disappear and dmesg :
saa7133[0]: found at 0000:01:09.0, rev: 208, irq: 5, latency: 64, mmio: 0xd8100000
saa7133[0]: subsystem: 11bd:002f, board: Pinnacle PCTV 110i (saa7133) [card=77,insmod option]
saa7133[0]: board init: gpio is 600e000
input: Pinnacle PCTV as /class/input/input5
ir-kbd-i2c: Pinnacle PCTV detected at i2c-2/2-0047/ir0 [saa7133[0]]
tda9887 2-004b: chip found (at) 0x96 (saa7133[0])
i2c eeprom 00: bd 11 2f 00 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: ff e0 60 06 ff 20 ff ff 00 30 8d 2c f5 37 ff ff
saa7133[0]: i2c eeprom 20: 01 2c 01 02 02 01 04 30 98 ff 00 a5 ff 21 00 c2
saa7133[0]: i2c eeprom 30: 96 10 03 32 15 20 ff ff 0c 22 17 88 03 48 ca 0c
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
but with tvtime-scanner -n PAL and KDETV no signal :(
so i unload saa7134 ad try to load saa7134 card=81 and later saa7134_dvb....dmesg say :
saa7133[0]: found at 0000:01:09.0, rev: 208, irq: 5, latency: 64, mmio: 0xd8100000
saa7133[0]: subsystem: 11bd:002f, board: Philips Tiger reference design [card=81,insmod option]
saa7133[0]: board init: gpio is 600c000
tda9887 2-004b: chip found (at) 0x96 (saa7133[0])
saa7133[0]: i2c eeprom 00: bd 11 2f 00 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: ff e0 60 06 ff 20 ff ff 00 30 8d 2c f5 37 ff ff
saa7133[0]: i2c eeprom 20: 01 2c 01 02 02 01 04 30 98 ff 00 a5 ff 21 00 c2
saa7133[0]: i2c eeprom 30: 96 10 03 32 15 20 ff ff 0c 22 17 88 03 48 ca 0c
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Fsaa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
DVB: registering new adapter (saa7133[0]).
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
i think that's all is correct...but no signal everywhere tvtime-scanner and kdetv...
where's my error?? pleaase help me ;
thanks in advance
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request (at) redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list