By Date: <-- -->
By Thread: <-- -->

pinnacle 878a radio not work

I have follow hardware:

PINNACLE EMPTYV 2.4
Philips TDA 9887 ST
Micronas MSP-3410G B11
Conexant Fusion 878A

and this software config:
linux kernel 2.6.15.1

The TV works, but the radio has no sound:

modprobe bttv

bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, low) -> 
IRQ 21
bttv0: Bt878 (rev 17) at 0000:01:08.0, irq: 21, latency: 32, mmio: 0xf0000000
bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00fffbff [init]
msp3400 2-0040: chip=MSP3410G-B11 +nicam +simple +simpler +radio mode=simpler
msp3400 2-0040: msp34xxg daemon started
tda9887 2-004b: chip found  (at)  0x96 (bt878 #0 [sw])
tuner 2-0060: Chip ID is not zero. It is not a TEA5767
tuner 2-0060: Setting mode_mask to 0x0e
tuner 2-0060: chip found  (at)  0xc0 (bt878 #0 [sw])
tuner 2-0060: tuner 0x60: Tuner type absent
bttv0: i2c: checking for MSP34xx  (at)  0x80... found
bttv0: pinnacle/mt: id=2 info="PAL+SECAM / stereo" radio=yes
bttv0: using tuner=33
tuner 2-0060: Calling set_type_addr for type=33, addr=0xff, mode=0x0c
tuner 2-0060: MT20xx hexdump: 42 98 1a 00 cc 64 10 88  29 08 85 99 e3 92 f0 10  
24 3c bf 42 98
tuner 2-0060: microtune: companycode=3cbf part=42 rev=98
tuner 2-0060: mt2050: sro is 92
tuner 2-0060: microtune MT2050 found, OK
tuner 2-0060: bt878 #0 [sw] tuner I2C addr 0xc0 with type 33 used for 0x0e
tuner 2-0060: pinnacle pal
bttv0: i2c: checking for MSP34xx  (at)  0x80... found
bttv0: i2c: checking for TDA9875  (at)  0xb0... not found
bttv0: i2c: checking for TDA7432  (at)  0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
tuner 2-0060: Unimplemented IOCTL 0x40046d11(dir=1,tp='m',nr=17,sz=4)
tuner 2-0060: Unimplemented IOCTL 0x40046d11(dir=1,tp='m',nr=17,sz=4)
bttv0: PLL: 28636363 => 35468950 . ok
tuner 2-0060: Cmd VIDIOCSCHAN accepted for analog TV
tuner 2-0060: mt2050_set_if_freq freq=400000000 if1=1218000000 if2=38900000
tuner 2-0060: mt2050: enabled antenna connector 1

when I do a "radio -f 102.5" I got:

tuner 2-0060: Cmd AUDC_SET_RADIO accepted for radio
tuner 2-0060: Unimplemented IOCTL 0x40046d11(dir=1,tp='m',nr=17,sz=4)
tuner 2-0060: Cmd VIDIOCGTUNER accepted for radio
tuner 2-0060: Cmd VIDIOCSFREQ accepted for radio
tuner 2-0060: radio freq set to 102.50
tuner 2-0060: mt2050_set_if_freq freq=102500000 if1=1218000000 if2=33300000
tuner 2-0060: mt2050: enabled antenna connector 0
tuner 2-0060: Cmd VIDIOCGAUDIO accepted for radio
tuner 2-0060: Unimplemented IOCTL 0x40046d11(dir=1,tp='m',nr=17,sz=4)
tuner 2-0060: Cmd VIDIOCSAUDIO accepted for radio
tuner 2-0060: VIDIOCSAUDIO not implemented.
tuner 2-0060: Cmd VIDIOCGAUDIO accepted for radio
tuner 2-0060: Unimplemented IOCTL 0x40046d11(dir=1,tp='m',nr=17,sz=4)
tuner 2-0060: Cmd VIDIOCSAUDIO accepted for radio
tuner 2-0060: VIDIOCSAUDIO not implemented.
tuner 2-0060: Cmd VIDIOCSFREQ accepted for radio

The program show a radio MONO instead of stereo as is and the AUDIO not work.

some suggestion ?


thnx lore

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request (at) redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list